← Feature Explorer
FOW-VEN-036Low
Dust Collection – Building 100
Dust Collection – Building 100: design, construction and commissioning within a defense energetics production facility.
Most Restrictive Requirement
NFPA 654NFPA 654 / NFPA 652 dust hazard analysis governs dust handling; ATEX zoning alone is not accepted.
Design Criteria
Summary
- Discipline
- Mechanical
- Category
- Ventilation
- Risk Level
- Low
- Approval Authority
- Fire Protection Engineer
- Standards Applied
- 8 across 8 families
- Verified Links
- 2 of 8 approved
- Common Equipment
- Dust Collector, Explosion Isolation Valve, Wet Scrubber
Applicable Standards (8)
Hazardous Areas
- NFPANFPA 654governsReviewedPrevention of Fire and Dust Explosions
- NECNEC Art. 506DraftZone 20, 21, 22 Locations
- IECIEC 60079-14ApprovedElectrical Installations Design in Ex Areas
- ATEX1999/92/ECApprovedATEX Workplace Directive
- DINDIN EN 14373ReviewedExplosion Suppression Systems
Mechanical
- UFCUFC 3-410-01ReviewedHeating, Ventilating, and Air Conditioning Systems
- UFGSUFGS 22 05 00ReviewedCommon Work Results for Plumbing
Environmental
- EPA40 CFR 68ReviewedRisk Management Program
Governing Authorities
- LeadFire Protection EngineerQualified Fire Protection Engineer · Fire suppression, detection, life safety
- Electrical Safety AuthorityElectrical AHJ · Electrical installations, arc flash, hazardous locations
Highest Risk Items
- Dust deflagration in collection systemCriticalRemote operation, shielding per UFC 3-340-02, and explosives safety review prior to start-up.
- Inadequate hazardous ventilationHighEngineering controls, third-party verification and AHJ acceptance testing.
Known U.S. / European Conflicts (16)
NEC Art. 505↔IEC 60079-14· Zone installationsSimilar
Requirements broadly equivalent; document equivalency in design analysis.
NFPA 69↔DIN EN 14373· Explosion suppressionPartial
Partial alignment; supplemental U.S. testing or documentation required.
NFPA 654↔VDI 2263· Combustible dustPartial
Partial alignment; supplemental U.S. testing or documentation required.
29 CFR 1910.119↔1999/92/EC· Process safety / workplace explosionSignificant Difference
Fundamental differences; requires AHJ/NRTL review and likely redesign or re-certification.
NEC Art. 506↔IEC 60079-10-2· Dust zone classificationSimilar
Requirements broadly equivalent; document equivalency in design analysis.
UFC 4-020-01↔IEC 60079-14· Motor efficiencyPartial
Partial alignment; supplemental U.S. testing or documentation required.
NFPA 654↔EN 1993· Emergency stop circuitsPartial
Partial alignment; supplemental U.S. testing or documentation required.
IEEE 142↔IEC 60079-14· Transformer designPartial
Partial alignment; supplemental U.S. testing or documentation required.
UFGS 22 05 00↔2014/34/EU· Switchgear testingPartial
Partial alignment; supplemental U.S. testing or documentation required.
UFC 3-410-01↔EN 764-7· VibrationSignificant Difference
Fundamental differences; requires AHJ/NRTL review and likely redesign or re-certification.
UFGS 25 05 11↔IEC 60079-14· Fire dampersPartial
Partial alignment; supplemental U.S. testing or documentation required.
40 CFR 68↔EN 1993· Hazardous waste labelingPartial
Partial alignment; supplemental U.S. testing or documentation required.
UFGS 28 31 76↔IEC 60079-14· Lifting gearPartial
Partial alignment; supplemental U.S. testing or documentation required.
NFPA 20↔IEC 60079-14· Grounding gridsPartial
Partial alignment; supplemental U.S. testing or documentation required.
NEC Art. 506↔EN 1993· Anchor boltsPartial
Partial alignment; supplemental U.S. testing or documentation required.
UFC 3-401-01↔IEC 60079-14· HydrotestPartial
Partial alignment; supplemental U.S. testing or documentation required.